Descriptions of Linko RT Series Cross Flow Cooling Tower(Part1/3)

Linko RT Series Cross Flow Cooling Tower (1/3)

Linko RT series cross flow cooling tower adopts air inlets on both sides and fans at the top allows the air to exchange medium with hot water through the fillers on both sides of the tower, and the hot and humid air is discharged outside the tower. The filler adopts a point wave plate with convex points on both sides, and the point wave plate is bonded into a whole through the installation head to improve rigidity. The convex points on both sides can also avoid direct dripping, so the water film forming ability is improved, and the tail of the filler Water measures. 

Features:

1. Space saving and light structure

The use of high-efficiency heat exchange packing designed specifically for this series of cooling towers greatly increases the heat exchange area. Due to the optimization of the structural design and the use of steel structure, the running weight is also greatly reduced.

2. Save electricity

The use of fillers with low ventilation resistance and wing-type aluminum alloy high-efficiency fans specially designed for cooling towers reduces the power of the motor used. The ultra-low noise type uses less motor power and saves power. Requirements, equipped with a two-speed motor to save power.

3. Very low operating noise

Choose low-speed space-twisted forward-tilt aluminum alloy small and medium-sized cooling tower dedicated fan. The salient features are light weight, large air volume, low noise, low energy consumption and long life. The angle of the fan can be adjusted to meet the different needs of customers in terms of air volume and other processes. It has the following advantages:

1). High fan efficiency: The cooling tower fan is a large-blade fan, with a large blade width, large chord length, and space distortion. It has a high pressure coefficient and flow coefficient, and can achieve a high air volume and a low air flow rate under the premise of lower speed. Wind pressure value, and can meet the requirements of reducing noise.

2) Good strength performance: Aluminum alloy fan has good strength, good dynamic balance, stable operation, good temperature resistance, and is not easy to deform. Ultra-low noise series cooling towers have lower operating noise and fully comply with environmental protection requirements.

If equipped with a two-speed motor, the noise can be further reduced by 2-3dB (A) during low-speed operation at night. Users who require a two-speed motor should separately request when ordering.

4. Good corrosion resistance

The tower body, sink and panel are made of FRP material with good corrosion resistance, and a light stabilizer is added to the gel coat resin, which has good anti-aging properties and does not change color over time. The steel structure of the tower body is galvanized after processing to improve the corrosion resistance of the cooling tower. In the normal service life, no additional anti-corrosion is required.

Z700 galvanized steel frame structure

 5. Easy combination

     Combination methods can be used to meet the requirements of different working conditions, users can also decide the combination according to the site conditions, and can adjust the appearance of the cooling tower according to the user's building characteristics. If the user site is very limited. Our company can also design according to the special requirements of users to meet the requirements of users on thermal performance and noise.

6. Easy maintenance

This series of cooling towers is a combined design. The air chambers of adjacent cooling towers are separated from each other. Maintenance and repairs can be carried out under the premise of normal operation of the cooling tower. The work of cleaning the packing, water accumulation pipes and water tank is more convenient.

Convenient cross-flow tower combination and easy maintenance
product structure:

(1) Panel: FRP material, smooth and beautiful surface, corrosion resistance, anti-aging.

(2) Filler: Modified PVC bidirectional point wave plate, good thermal performance, small air flow resistance, good rigidity, heat resistance 75 ℃, cold resistance, flame retardant.

(3) Fan: The blade material is alloy aluminum plate. The fan has reasonable aerodynamic force, large air volume, high efficiency, low noise and corrosion resistance.

(4) Motor and reducer: for external equipment.

(5) Cloth sink: FRP material, uniform water distribution, ultra-low noise type with cover plate can shield the light, prevent debris from flying in, reduce the splashing sound.

(6) Muffler cover: glass fiber reinforced plastic, flame retardant PVC film muffler material with internal sticky cavity.

(7) Blinds: glass fiber reinforced plastic material, which can be waterproof and splashed out, and can make the air flow into the tower even.

(8) Water tank: made of glass fiber reinforced plastic, it plays a role of water collection, and has automatic water replenishment facilities, which can directly absorb water in a closed circuit.

(9) Skeleton: It is a folded steel assembled structure, with good rigidity, light weight, easy transportation and installation, hot plating.

PS: Not finished. More information about RT series, pls pay attention to the next news "Linko RT Series Cross Flow Cooling Tower (2/3)".

Thank you so much!